Fujitsu Semiconductor Europe - Program Download. ▫ Start the FUJITSU FLASH MCU Programmer. ▫ Select the target.

1 FUJITSU FLASH MCU Programmer for F 2 MC-16LX Specifications 2 FUJITSU FLASH MCU Programmer for F 2 MC-16LX Specifications Version September 2008 Software version: V01L FUJITSU LIMITED Printed in Japan 1. Circuit diagrams utilizing Fujitsu products are included as a mean of illustrating typical semiconductor applications. Complete information sufficient for construction proposes is not necessarily given.

Kenwood amplifier a 5j manual. Category People & Blogs; Song Let's Talk About a Man (feat. Marvin) [Extended Version] Artist Prezioso; Album Let's Talk About a Man (feat. Kenwood Car Amplifier Manual. Read and download pdf kenwood kenwood amplifier a 5j swes manual. Ebooks document. Kenwood car amplifier owners manual. Find great deals on eBay for Kenwood TL-922 in Ham Radio.

The information contained in this document has been carefully checked and is believed to be reliable. However, Fujitsu assumes no responsibility for inaccuracies. The information contained in this document does not convey any license under the copy right, patent right to trademarks claimed and owned by Fujitsu. Fujitsu reserved the right to change products or specifications without notice. No part of this publication may be copied or reproduced in any form or by any means, or transferred to any third party without prior written consent of Fujitsu. The products described in this document are not intended for use in equipment requiring high reliability, such as marine relays and medical life-support systems. For such applications, contact your Fujitsu sales representative.

If the products and technologies described in this document are controlled by the Foreign Exchange and Foreign Trade Control Act established in Japan, their export is subject to prior approval based on the said act. 19 (c) Select the COM port of the PC connected to the user system. Click the [Set Environment] button in the main dialog box to open the setup window. When the [COM PORT] tab in the setup window is clicked, the specifying window is opened. Select any of the following COM ports. COM1, COM2, COM3, COM4, COM5, COM6, COM7, COM8,COM9,COM10 COM11, COM12, COM13, COM14, COM15, COM16, COM17, COM18,COM19,COM20 (d) Execution of downloading Click the [Download] button. If the following dialog window is opened, Input a reset signal to the microcontroller to start the program in the flash programming mode and then click the [OK] button Downloading is performed to open the Download window.

When downloading is completed normally, the following dialog window opens. Instant immersion 36 languages deluxe v30 edgeiso. When the [OK] button is clicked to close the dialog window, the [Erase], [Blank Check], [Program & Verify], [Read & Compare] and [Copy] buttons are enabled. Note: Downloading can also be performed using the Tab key to move to the [Download] button and pressing the Enter key or pressing the ALT and D keys at the same time.

13 20 7.2 Erasing and Programming This section explains how to specify Hex File and the processing and operation performed when the [Erase], [Blank Check], [Program & Verify], [Read & Compare], [Copy] and [Full Operation (D+E+B+P)] buttons are clicked. Each execution can also be performed by pressing the key corresponding to the underlined character in the button name while pressing the ALT key. (Hex File is a O character in Open button, click the ALT + O keys).

(a) Hex File: Select the file to be programmed to flash memory Specify the Motorola-S or Intel-HEX format file to be programmed to flash memory in the microcontroller. Although the specification method by drags and drops a direct file from Explorer etc. Is recommended, it can specify also by the file appointed window displayed by pushing the [Open] button. Hex File must be specified to execute [Program & Verify], [Read & Compare] and [Full Operation (D+E+B+P)]. Since it is decoded at the head of these processings each time, even if the specified Motorola S or Intel-HEX format file changes specification of a file just before processing, it is OK.

(b) Erase: Erase all flash memory areas All flash memory must be in the erase state (0xff) when programming a new program to it. By pushing this button, a chip erase command is published to FLASH and elimination is performed. In addition, a blank check does not perform this command. (c) Blank Check: Check that all flash memory areas are blank This button is clicked to check that all flash memory is in the erase state (0xff). 14 21 (d) Program & Verify: Program data to flash memory This button is clicked to program the Motorola-S or Intel-HEX format file specified in Hex File to flash memory in the microcontroller concurrently with verification. An error dialog is displayed, when writing is performed for 512 bytes of every block and a CRC error is detected by the block.

This dialog If YES is pushed, the block of an error will be resent and it will continue writing. A push on NO interrupts write-in processing. (e) Read & Compare: Compare Hex File with data in flash memory in microcontroller This button is clicked to compare data in the Motorola-S or Intel-HEX format file specified in Hex File with data in flash memory in the microcontroller. Like the [Program & Verify] processing, The data of FLASH is transmitted for 512 bytes of every block, a CRC error check is performed, and comparison processing is performed. (f) Copy: Save data in flash memory in microcontroller to file This button is clicked to read data from flash memory integrated into the microcontroller and save it as an Motorola-S or Intel-HEX format file. Like [Read & Compare] processing, FLASH memory reading is performed for 512 bytes of every block, and a CRC error check is performed similarly.